Step 1: Turn the paddle retention clip on the back counterclockwise (left) by 30 degrees.

Step 2: Remove the retention clip, then remove or attach the paddle as desired.

Step 3: To reinstall, cover the clip starting from the 30-degree left-angled position and turn it clockwise (right) by 30 degrees.

Completion: Your Void INTUITION paddle removal/installation is now complete.

　　　　　Note: Ensure the controller is powered on while performing these steps.

　　　　　　　　If remapping is not possible, press and hold the PS (Home) button for 10 seconds to turn off 

　　　　　　　　the power, then press the PS (Home) button again to power it back on and retry.

　　　　　　　　Please note that remapping cannot be performed if the battery is low.

　　　Step 1: Enter Remapping Mode

　　　　　Press and hold L1 + R1 + X + Square buttons simultaneously for more than 5 seconds.
　　　　　When the LED next to the touchpad flashes red, remapping mode is activated.

　　　Step 2: Profile Selection

 　　　　　While in remapping mode, the following actions will allow you to select a profile:

　　　　　　　・D-pad Up: Profile 1 (LED flashes red once)

　　　　　　　・D-pad Right: Profile 2 (LED flashes red twice)

　　　　　　　・D-pad Down: Profile 3 (LED flashes red three times)

　　　　　　　・D-pad Left: Profile 4 (LED flashes red four times)

　　　　　Note: The profile feature allows you to save the remapping settings assigned to the rear paddles.

　　　Step 3: Assigning Rear Paddles

　　　　　Press the rear paddle you wish to assign while pressing the desired key or button, then release both simultaneously.

　　　　　When the LED flashes red, it indicates the assignment was successful.

　　　　　To unassign a rear paddle, simply press and release the paddle without pressing any buttons.

　　　Step 4: Save & Apply

　　　　　Press the X button to save the remapping settings and exit remapping mode.

　　　　　Example Setting

　　　　　　During Step 3, press and release the triangle button while pressing the rear paddle.

　　　　　　After saving in Step 4, pressing the relevant rear paddle will trigger the triangle button response.

　　　Remapping Reset Method

　　　　　If issues occur, such as unintended repeated pressing of the rear paddles, reset the remapping settings:

　　　　　　１．With the controller powered off,
　　　　　　　　press and hold the Circle, Cross, Square, and Triangle buttons simultaneously for more than 5 seconds.

　　　　　　２．While holding the buttons, turn the power back on. If the LED flashes red for about 3 seconds, the reset is complete.

　　　　　Note: Ensure the controller is powered on while performing these steps.

　　　　　　　　If remapping is not possible, press and hold the PS (Home) button for 10 seconds to turn off the power,
　　　　　　　　then press the PS (Home) button again to power it back on and retry.

　　　　　　　　Also, be aware that remapping cannot be performed if the battery level is low.

　　　Step 1: Enter Remapping Mode

　　　　　Press and hold L1, L2, R1, and R2 simultaneously for 8 seconds.

　　　　　The LED on the mute button will light up red for 1 second, indicating you are now in programming mode.

　　　　　Note:If the light is weak, please try in a darker environment.

　　　Step 2: Profile Selection

　　　　　While in remapping mode, the following actions will allow you to select a profile:

　　　　　　　・D-pad Up: Profile 1 (LED flashes red once)

　　　　　　　・D-pad Right: Profile 2 (LED flashes red twice)

　　　　　　　・D-pad Down: Profile 3 (LED flashes red three times)

　　　　　　　・D-pad Left: Profile 4 (LED flashes red four times)

Note: The profile feature allows you to save the remapping settings assigned to the rear paddles.

　　　Step 3: Assigning Rear Buttons

　　　　　While holding down the rear button you want to assign,
　　　　　press the key or button you want to set, and then release them simultaneously.

　　　　　The LED will flash red, indicating that the assignment was successful.

　　　　　If you want to set the rear button to "none," simply press and release the rear button only.

　　　Step 4: Save & Apply

　　　　　Press the X button to save the remapping settings and exit remapping mode.

　　　　　Example of Settings:

　　　　　　　In Step 3, press and hold the rear button while pressing △, then release them simultaneously.

　　　　　　　After saving the settings in Step 4, pressing the corresponding rear button will trigger △.

　　　Profile Switching

　　　　　By pressing L1 + R1 + X + □ buttons along with the profile selection button (D-pad),
　　　　　you can switch profiles without entering remapping mode.

　　　Reset Method

　　　　　If issues occur, such as unintended repeated pressing of the rear buttons, reset the remapping:
　　　　　With the controller powered off,
　　　　　press and hold the Circle, Cross, Square, and Triangle buttons simultaneously for more than 5 seconds.
　　　　　While still holding these buttons, turn the controller's power back on.

　　　　　If the LED on the mute part flashes red for about 3 seconds, the reset is complete.

　　　　　Note: Ensure the controller is powered on while performing these steps.

　　　　　　　　If remapping is not possible, press and hold the PS (Home) button for 10 seconds to turn off the power,
　　　　　　　　then press the PS (Home) button again to power it back on and retry.

　　　　　　　　Also, be aware that remapping cannot be performed if the battery level is low.

　　　Step 1: Enter Programming Mode

　　　　　Press and hold L1, L2, R1, and R2 simultaneously for 8 seconds.

　　　　　The LED on the mute button will light up red for 1 second, indicating you are now in programming mode.

　　　　　Note:If the light is weak, please try in a darker environment.

　　　Step 2: Assigning Rear Buttons

　　　　　While pressing the rear button you wish to assign, press the desired key or button, then release both simultaneously.
　　　　　If the LED on the mute part flashes red, the assignment is successful.

　　　　　Note: If you want to unassign a rear button, simply press and release that button only.

　　　Step 3: Save & Apply

　　　　　Press the up arrow on the D-pad to save and activate the assigned settings.

　　　　　If the LED on the mute part lights up red for 1 second, the save and apply process is complete.

　　　　　Example Setting

　　　　　　　　In Step 2, press a rear button while pressing Triangle, then release both simultaneously.

　　　　　　　　After saving in Step 3, pressing the relevant rear button will trigger the Triangle response.

　　　Reset Method

　　　　　If issues occur, such as unintended repeated pressing of the rear buttons, reset the remapping:
　　　　　With the controller powered off,
　　　　　press and hold the Circle, Cross, Square, and Triangle buttons simultaneously for more than 5 seconds.
　　　　　While still holding these buttons, turn the controller's power back on.

　　　　　If the LED on the mute part flashes red for about 3 seconds, the reset is complete.

　　　　　Note: Ensure the controller is powered on while performing these steps.

　　　　　　　　If remapping does not work, press and hold the PS (Home) button for 10 seconds to turn off the power,
　　　　　　　　then press the PS (Home) button again to power it back on and retry.

　　　　　　　　Also, remapping cannot be performed if the battery level is low.

　　　Step 1: Enter Programming Mode

　　　　　Press and hold L1, L2, R1, and R2 simultaneously for 8 seconds.

　　　　　The LED on the touchpad (located at the upper middle front) will flash red once.

　　　　　Note: Please be aware that if the controller is charging, the LED light may be difficult to see.

　　　Step 2: Assigning Rear Buttons

　　　　　While pressing the rear button you wish to assign, press the desired key or button, then release both simultaneously.

　　　　　If the LED on the touchpad flashes red, the assignment is successful.

　　　　　Note: If you want to unassign a rear button, simply press and release that button only.

　　　　　Note: Inputs that cannot be replicated with an original controller will not work.
　　　　　(For example, you cannot register both left and right or up and down on the rear buttons to be pressed at the same time.)

　　　Step 3: Save & Apply

　　　　　To save and activate the assigned settings, press the touchpad button once.

　　　　　If the LED on the touchpad lights up red for 1 second, the save and apply process is complete.

　　　　　Example Setting

　　　　　　In Step 2, press a rear button while pressing Triangle, then release both simultaneously.

　　　　　　After saving in Step 3, pressing the relevant rear button will trigger the Triangle response.

　　　Remapping Reset Method

　　　　　If issues such as unintended repeated pressing of the rear paddles occur, reset the remapping:

　　　　　　１．With the controller powered off,
　　　　　　　　press and hold the Circle, Cross, Square, and Triangle buttons simultaneously for more than 5 seconds.

　　　　　　２．While still holding these buttons, turn the controller's power back on.
　　　　　　　　If the LED on the touchpad flashes red 10 times, the reset is complete.

　　　　　Note: Make sure the controller is either battery-powered or connected via cable with the Void mark button illuminated.

　　　　　　　　The profile feature is designed to store the settings of the rear buttons.

　　　◆Profile Feature:

　　　　　Each double click of the button within the circular frame on the paper image
　　　　　switches the profiles sequentially from 1 onwards.

　　　▼Profile Colors:

　　　　　【Profile 1: Dark Blue】【Profile 2: Green】【Profile 3: Light Blue】

　　　　　【Profile 4: Lime Green】【Profile 5: Purple】【Profile 6: Pale Blue】

　　　　　【Profile 7: No light】 (The rear buttons are inactive in this profile).

　　　Step 1: Enter Programming Mode

　　　　　After selecting the desired profile,
　　　　　press and hold the button within the circular frame on the paper image for about 3 seconds.

　　　　　The LED will flash the color of the currently selected profile, indicating that you have entered programming mode.

　　　Step 2: Assigning Rear Buttons 

　　　　　While pressing the button you wish to configure, press and hold one of the rear buttons (K1, K2, K3, K4) for about 2 seconds.

　　　　　If the LED flashes red rapidly, the assignment is complete.

　　　　　Note: To unassign a button,
　　　　　　　　press and hold both the currently assigned button and the rear button (K1, K2, K3, K4) you wish to unassign.

　　　　　　　　If the assignment is successfully removed, the LED will flash red slowly three times.

　　　　　【Example:】

　　　　　If the rear button (K2) is assigned to the B button,
　　　　　pressing and holding both the rear button (K2) and the B button will unassign it.

　　　Step 3: Save & Apply

　　　　　To save the settings and activate the rear button assignments, press and hold the button within the circular frame on the 　　　　　paper image again for about 3 seconds. Once the LED changes from flashing to solid, the settings are complete.